How to measure for roller blinds
Ten minutes with a steel tape measure is all it takes. Here's how to measure so your blind fits the first time, whether it sits inside the window recess or over the frame.
The short version
- Decide on an inside fit (inside the recess) or an outside fit (over the frame).
- Use a steel tape and measure in millimetres.
- Inside fit: measure the recess width at the top, middle and bottom and use the narrowest. Measure the drop on the left, middle and right and use the longest. Give us the exact recess size and don't deduct anything yourself.
- Outside fit: give the finished size you want, overlapping the frame by at least 50 mm each side.
- Check the recess depth, and note anything that sticks out: handles, winders, locks.
Inside fit or outside fit?
Choose this first, because it changes what you measure.
Inside fit
The blind sits within the window recess. It looks neat and built-in and shows off the architrave. Expect a fine line of light at each edge, because the blind has to be slightly narrower than the opening to roll freely.
Outside fit
The blind is fixed to the wall or frame and covers the whole opening. It blocks more light at the edges, which makes it the better choice for bedrooms and nurseries, and it suits shallow recesses or windows with handles in the way.
If your recess is deep enough and has nothing in the way, inside fit is the usual choice for living areas. For a properly dark bedroom, outside fit is the better pick.
What you'll need
- A steel tape measure. Fabric tapes stretch.
- A pencil and something to write on, or your phone's notes.
- A name for each window, such as "Main bedroom left", so nothing gets mixed up when you order.
Measuring for an inside fit
1. Width
Measure the inside of the recess, from wall to wall, at the top, middle and bottom. Walls are rarely perfectly straight, so the three readings often differ by a few millimetres. Use the narrowest, so the blind can't jam on the tightest point.
2. Drop
Measure from the top of the recess to the sill on the left, middle and right, and use the longest. A roller blind can always stop short; it can't grow.
3. Depth
Measure how deep the recess is, from the window frame or glass to the front edge of the reveal. The rolled-up blind and its brackets need flat depth to sit in. Most standard roller blinds need somewhere around 50 to 80 mm, depending on the size and fabric. A longer drop rolls up thicker. We'll confirm the exact minimum on each product before you order.
While you're there, check for anything sticking out: window handles, winders, locks or security screens. Measure the depth to the front of whatever protrudes, not to the glass.
4. Don't deduct anything
Measuring for an outside fit
- Width: measure the outside of the frame, then add at least 50 mm on each side. The more overlap, the less light gets around the edges.
- Drop: measure from where the brackets will go, usually 50 to 100 mm above the frame, down to where you want the blind to finish. That's normally the sill, or about 50 mm below it if there's no sill.
- Check the fixing surface: make sure there's solid wall or frame where the brackets will go, and nothing in the way: cornices, light switches, curtain tracks or air-conditioning vents.
For an outside fit, the size you give us is the size of the blind.
The mistakes that cause remakes
| Mistake | What happens | How to avoid it |
|---|---|---|
| Measuring in centimetres and rounding | The blind can be up to 5 mm out, enough to jam or leave a gap | Measure and order in millimetres |
| Deducting for an inside fit yourself | The allowance is taken twice and the blind is too narrow | Give the exact recess size |
| Measuring only one width | The blind catches on the narrowest point | Measure the top, middle and bottom |
| Swapping width and drop | A blind turned on its side | Width is always side to side, written first |
| Forgetting a handle or winder | The blind hits it when lowered | Measure depth to the front of anything that sticks out |
| Using a fabric tape | The measurements stretch | Use a steel tape |
Choosing the control side
Stand facing the window and decide which side you want the chain on. Pick the side that's easy to reach and away from furniture, curtains and doors. For a pair of windows side by side, the chains usually look best on the outside edges.
A note on child safety
Looped cords and chains on blinds are a strangulation risk for young children. Under Australia's mandatory safety standards, blinds with cords or chains must come with warning labels, installation instructions and the safety parts needed to fit them safely, such as a chain tensioner. The installation standard requires the blind to be fitted so that a loose cord can't form a loop of 220 mm or more within 1,600 mm of the floor. In practice, that means fixing the chain tensioner to the wall when you install the blind. Keep cots, beds and climbable furniture away from windows. If you'd rather have no chain at all, ask about motorised blinds. More from Product Safety Australia.
Common questions
Should I measure the window or the blind size?
For an inside fit, give the exact recess size and the maker takes off the allowance. For an outside fit, give the finished size you want.
Which width do I use if my window isn't square?
The narrowest width and the longest drop, for an inside fit.
How much should an outside-fit blind overlap the window?
At least 50 mm each side, more for better blockout, with room above the frame for the brackets.
How deep does a recess need to be for an inside fit?
It depends on the blind, but most standard roller blinds need around 50 to 80 mm of flat depth. Measure past handles and winders.
Can I measure once for several identical windows?
Measure every window, even ones that look the same. Windows that look identical often differ by a few millimetres, and that's enough to matter on an inside fit.